MELLANOX CONNECTX EN MNPH29B-XSC DRIVER DETAILS:
|File Size:||9.5 MB|
|Supported systems:||Windows Vista (32/64-bit), Windows XP (32/64-bit), Windows 8, Windows 10|
|Price:||Free* (*Free Registration Required)|
MELLANOX CONNECTX EN MNPH29B-XSC DRIVER
All other marks Mellanox ConnectX EN MNPH29B-XSC names mentioned herein may be trademarks of their respective companies. Board Mechanical Drawing and Dimensions 23 A. I2C-compatible Connector Pinout 30 B. Revision History Table 6 Table 2: Documents List 7 Table 3: Hardware and Software Requirements 3 Table 6: Jumper Configuration 9 Table 7: Max Cable Lengths 22 Table 0: Product Label 2 Figure 3: Physical and Logical Link Indications 8 Figure 4: I2C Connector 9 Figure 5: I2C-Compatible Connector 30 Figure 8: Adapter Card 33 Figure: Adapter card With Bracket Removed 33 Figure 2: Placing the Bracket on the Card 34 Figure 3: It provides details as to the interfaces of the card, specifications, required software and firmware for operating the card, and relevant documentation. Intended Audience This manual is intended for the installer and user of these cards.
The manual assumes basic familiarity with Ethernet networks.
Reference for hardware engineers responsible for designing systems and boards. User s Manual describing the set of MFT firmware management tools.
See under Firmware downloads. Firmware download Web page: The use of Mb or Mbits small b indicates size in mega bits. The cards described in this manual have the following main features: These modules must be purchased separately from. Mellanox ConnectX EN MNPH29B-XSC and LR modules not recommended by Mellanox may not work with the adapter.
Hardware and Software Requirements Before installing the NIC, please make sure that the system meets the hardware and software requirements listed in Table 3. Support can be found at: Please consult the host machine documentation for instructions on how to install a PCI Express card. Any PCI slot with the proper configuration is acceptable for connection. If the card is installed in a PCI slot with less lanes than the Mellanox ConnectX EN MNPH29B-XSC requires then the adapter card will not provide the optimum data transfer.
ConnectX EN Dual Port Ethernet Network Interface Cards with SFP+ Connectors User s Manual - PDF
Installation Instructions Read all installation instructions before connecting the equipment to the power source. Over-temperature This equipment should not be operated in an area with an ambient temperature exceeding the maximum recommended: An air flow of LFM at Mellanox ConnectX EN MNPH29B-XSC maximum ambient temperature is required. Moreover, to guarantee proper air flow, allow at least 8cm 3 inches of clearance around the ventilation openings. During Lightning - Electrical Hazard During periods of lightning activity, do not work on the equipment or connect or disconnect cables. Equipment Installation This equipment should be installed, replaced, or serviced only by trained and qualified personnel.
Equipment Disposal Disposal of this equipment should be in accordance to all national laws and regulations. Local and National Electrical Codes This equipment should be installed in compliance with local and national electrical codes.
Hazardous Radiation Exposure Caution Use of controls or adjustment or performance of procedures other than those specified herein may result in hazardous radiation exposure. Make sure to open the Readme files and read them before you start the procedure. Mellanox ConnectX EN MNPH29B-XSC
ConnectX EN Dual Port Ethernet Network Interface Cards with SFP+ Connectors User s Manual
The installation requires administrator privileges on the target machine. Driver Software supplies drivers for: Download the driver from Mellanox website 2. Module parameters can be obtained with modinfo command: Within the tool kit is the mtsflint tool software package, which is also available at: You can download the Mellanox ConnectX EN MNPH29B-XSC firmware at: Follow the installation instructions included in the download package Updating Adapter Card Firmware Each adapter card is shipped with the latest version of qualified firmware at the time of manufacturing.
Firmware is updated occasionally, and the most recent firmware can be obtained from through the Firmware Mellanox ConnectX EN MNPH29B-XSC link, or you can download the latest firmware at: ConnectX EN Dual Port Ethernet Network Interface Cards With PCI Express x8 User's Manual.
3 Table Specifications for MNPH29B-XSC. MNPH29B-XSC, Rev X1/X2/X3/A1: MT_0BE, ConnectX® EN network interface card, dual-port, 10GBASE SFP+, PCIe x8 GT/s, mem-free, short.